19 SEER: 9000 BTU Ductless Air Conditioner Heat Pump Mini Split w/ install KIT

Description

Thermocore 9000 BTU AC-Heat 19 SEER
9000 BTU Ductless Mini Split AC: 19 SEER
Inverter w/ 9,000 BTU Heat Pump
Thermocore T4E19S-H209 Ductless Mini Split Heat Pump
–
9000 BTU  Cooling Capacity along with a 9,000 BTU Heat Pump, this 3/4 TON Ductless Split can cool or heat an area over 400 ft². 220 VAC OPERATION.Advanced INVERTER DC Technology provides both energy efficient operation and low ambient operation start-ups. Additional features include auto-diagnostic functions and sleep mode / 24 hour timer. Pre-charged with R410A and  includes 15ft install Kit.
Features
Specifications
Installation Kit
Inverter Technology
Setup – Installation
Warranty
Shipping
Available Accessories
Technical Data:
System Includes:
9,000 BTU
INVERTER
Cooling Capacity
9,000 BTU INVERTER Heat Pump
19 SEER – 9.5 HSPF
– AHRI Certified
*
Pre-Charged with ECO-Friendly R410A
1 Year Parts – 5 Year Compressor Warranty
View Details >
Indoor Unit – Air Handler.
Outdoor Unit – Compressor.
Digital Multi-function LCD Remote Control
Installation Kit with 15′ of lineset.>
Product and Installation Manual.  >>>
Top Line Features:
19 SEER – 9.5 HSPF – 11 EER
Pre-Charged w/ Eco-friendly R410A Refrigerant
Operates on Standard 220 VAC Power Input
Cross Flow Technology reduces noise output
Freon Leak Detection > Notification system
Low Ambient Temperature Operation (5° F)
Two-direction Air vane Evenly Distributes Air
Restart IC: Settings restored Following Outage
The  particle filter or “pre-filter” removes dust and other air-borne pathogens before pushing the air through additional filtration medias and the refrigeration coil array. This filter is washable and comes factory installed with every ductless air conditioner system.
Model Number
Thermocore T4E19S-H209
Compressor
TOSHIBA (GMCC)
Refrigerant
R410A (Pre-Charged)
Cooling / Heating Capacity
9000 BTU/ 9000 BTU
Air Flow
309/285/187 CFM
Power Supply
220 V / 60 Hz, 1Ph
Input Power
782W (cooling) / 925W (heating)
Rated Current
6.8A (Cooling) / 8.1A (heating)
Maximum Fuse
15A
Connection Wire
16 AWG/4:standard unshielded
SEER
19.0
EER
11
HSPF4
9.5
Sound Level
38/32/35(indoor) / 52dB  (outdoor)
Min Operating Temperature
– 15 C / 5 F
Net Weight
17.2 Lbs (Indoor) / 66.8 Lbs (Outdoor)
Dimensions (WXDxH)
28.43 x 7.36 x 11.42 in (Indoor Unit) – 30.31 x 11.81 x 21.85 in (Outdoor Unit)
Warranty
1 Year on Parts / 5 Years on Compressor
Install Kit Contents:
15 Feet Flared Copper Tubing
15 Feet Pipe Insulation
15 Feet Electrical Wire Harness
Drain Pipe (Indoor)
Indoor wall Mounting Bracket
Remote Control Wall Bracket
Wall Hole Block Putty & Insulated Tape
WHAT IS DC INVERTER?
DC Inverter Air Conditioners are the ultimate cooling technology of the HVAC field. They are called “DC inverter” because the alternative current (AC) is converted to Direct Current (DC) then, direct current inverted back to Alternative current with desired frequency. The current supplied through the wall outlet has fixed frequency which is 60 Hertz. Different frequencies supplied to the compressor will result in different running speeds of the compressor. Inverter control systems use Pulse Amplitude Modulation (PAM) that is the most advanced and energy efficient method of inverting the current. DC Inverter AC’s bear special compressors that their speed could be changed by increasing or decreasing the frequency of the supplied power. Therefore, unlike conventional split Air Conditioners Pumps which cycle between on and off repeatedly, the DC Inverter control system will monitor the room temperature and adjust the compressor speed automatically.
Conventional compressors turn on and off to maintain the room temperature at desired level. This will result compressor to draw tremendous energy each time it starts up. This will also reduce the life-span of the compressor and other components that are turning on and off. Once a conventional system is running, it runs at its maximum speed, consuming the maximum amount of energy in order to produce the maximum of cooling to maintain the desired temperature. The system will then cycle between on and off in an effort to maintain this temperature. When a DC Inverter compressor initially starts up, it runs with a higher speed to bring the room temperature to desired level rapidly, Once the set temperature is reached, it slows down and adjust its capacity just to counter the heat loss or heat gain of the building. Constant temperature is maintained.
BASIC OVERVIEW:
The indoor unit is hung like a picture frame approximately 6 – 8 feet above the floor usually on an exterior wall. A 2-3 inch hole must be made behind the indoor unit in the exterior wall to run the refrigerant copper tubing, electrical wires and the condensate drain to the outside unit. The indoor unit and outdoor unit are connected to each other by means of refrigerant copper tubing and electrical cables. The condensing unit comes pre-charged with R410A Freon however, procedures such as conducting leak tests etc. are still important steps in ensuring proper functioning of a split AC. *Although installation may seem easy to some, certain tools and experience is necessary to complete setup of a mini split* Click for Installation Tip. It is highly advised a certified HVAC technician complete installation to be eligible for warranty. See warranty details below >
*5 Year Compressor – 1 Year on all other Parts*
Registration card will be sent with unit, this card should be completed by  an HVAC technician (installer). Installation of a mini split must be completed by a licensed HVAC (Heating, ventilating, & air conditioning) company to ensure any issues encountered in the future are not due to improper installation / workmanship.Even though mini split setup is below the expertise requirements of central AC systems, these are not “plug-n-play” units that can be properly installed without certain tools any prior HVAC – electrical knowledge.  The installation  includes electrical, gas, and  refrigerant connections and generally regulated by a multiple sets of laws,  codes and guidelines, at the federal, state and local levels. The  failure to properly install HVAC equipment can raise personal safety and  performance concerns.Warranty service – troubleshooting is provided through the contractor / installer and will be upheld as long as policies are observed. Once a non-defective unit is installed by a HVAC company, chances of anything going wrong are very slim and almost all contractors will guarantee there workmanship and provide future service free of charge (installation warranty). If it was determined that the unit is not functioning due to a defect and needs to be replaced, the part will be sent free of charge up to 1 year from date of purchase or 5 years for the compressor. If you receive a damaged or defective product, a replacement unit will be sent out Free of cost. Damaged / Defective product will be picked up and a brand new exchange will be shipped out.
SHIPS TO TO BOTH UNITED STATES AND CANADIAN LOCATIONS!
Our Thermocore systems ship via FedexGround or out of Warren, Michigan and will arrive in two seperate boxes. Transit time is usually between 4 to 5 business days from payment receipt depending on where you are geographically located. We do not require signature upon delivery for these shipments. We will ship to Canadian locations but please be advised of additional import brokerage charges that may be entailed when shipment crosses border. please contact our offices.
Condenser Ground Stand
– Provides Flat even surface
– Avoids debris obstruction
Price:
$73.00
Click for more Info
Lineset (1/4 x 3/8)
– Required for Installation
25ft – 30ft – 40ft – 50ft
Lengths
Price:
$38.00 > $134.00
Click for more Info
Condenser Bracket
– Mount your condenser at any height on an outdoor sidewall
Price:
$96.00
Click for more Info
Micro-Pump II
– Required when mounting air handler on Interior wall
Price:
$172.00
Click for more Info
Electrical Wire Harness
– 16/4 Electrical Wire Harness
– For Extending Evap. Length
Price:
$2.15 / ft
Click for more Info
Additional Remote Controls
– Spare remote controls for the T4 Series Ductless System
Price:
$42.00
Click for more Info
Filter Medias
– Inserts into Filter Screen Slot
– Choice of 4 Filtration Medias
Price:
$10.00 – $14.00
Click for more Info
Wired Thermostat
– Permanently Hard Mounts
– Controls Settings w/ Remote
Price:
$88.00
Click for more Info